연결은 잘되 있고,시스템 채크에서 scsi 바이오스에서 스커시 하드 다 잡히고 등등...
현재 제가 알고 있는것은 아래와 같습니다.
부팅가능한 도스디스켓 안에 ASPI8U2.SYS 넣는다
config.sys 파일 내용을 아래와 같이 만든다.
MENUITEM=ADAPTEC SCSI
DEVICE=A:\ASPI8U2.SYS
LASTDRIVE=Z
다시 플로피로 부팅한다 그러면 스커시 하드가 잡힌다?, 그다음 scsi to ide 젠더 펌웨어 업그래이드용 바이오스 업글 프로그램을 실행하면
근데 이렇게 하니깐 aspi 에러가 남니다.
좀 지도해주십시요. 부탁드립니다.
대충 원본은 다음과 같습니다. acard에서 나온 scsi to ide 젠더 바이오스 업글요령.......
Hello Sir,
The attached file is a firmware update utility using DOS mode which is more powerful than the Windows one.
Here is the procedure for you to use this utility:
1. Please prepare a DOS bootable diskette and copy the extracted files into the diskette. Please choose to overwrite all the repeated files in the bootable diskette.
2. Reboot your system from the DOS bootable diskette and follow the instruction to update firmware for the defective bridges.
Important Notice: I send the flash utility to you privately. Please do not give it to your friend or even put it onto the internet. Otherwise, I will not be able to serve you in ACARD.
Thanks & Best regards,
ACARD Technology Corp.
FAE-Kent
Mail: ****@*****.com
Tel: 886(2)85122290 Ext: 3272
----- Original Message -----
From: 최영우(youngwoo choi)
To: Kent
Sent: Friday, November 18, 2005 1:13 PM
Subject: Re: i need help
hello kent ^^
my scsi adapter is on board scsi
SCSI • Adaptec AIC-7899W Controller
• Dual-Channel Ultra160 SCSI
look at http://www.supermicro.com/products/motherboard/P3/HE-SL/P3TDE6-G.cfm
thank you for your help ^^
----- Original Message -----
From: Kent
To: 최영우
Cc: RichardLee ; RichardChen ; KentLiu ; JeffHsiao ; JaneKu ; Samson
Sent: Friday, November 18, 2005 9:55 AM
Subject: Re: i need help
Hello Sir,
Can you tell me the model name of the SCSI host adapter?!
So that I can check if there is a solution for you to fix the problem.
Thanks for writing!
Your comments make our service improved.
ACARD Technical Support Dept.
FAE-Kent
Mail: ****@*****.com
Tel: 886(2)85122290 Ext: 3272
----- Original Message -----
From: 최영우
To: ****@*****.com
Sent: Thursday, November 17, 2005 5:44 PM
Subject: i need help
hello, kent
thank you for message of your opinion.
situation is like this......
in 2003, i bought 4 AEC-7726H from korea' seller
i have p3tde6 mainboard which is made in supermicro company.
4 AEC-7726H were connected WD 200GB hard driver.(each scsi id is 1,12,14,15)
connections are no problem.
one month ago, two of AEC-7726H were not working
when computer is booted, scsi check message is below.
scsi channel :A id :1, 12 scsi : null , capacity: 1MB, speed:80MB...........
the other AEC-7726H are working perfectly.......
so, i changed position of AEC-7726H.
consequently, when i changed position of two AEC-7726H, good working AEC-7726H were working perfectly.
bad AEC-7726H displayed same error.
and..
i can't find korea seller. i think that korea distributer is bankrupt...
if not, can you tell me korea distributer?
sorry for my poor english.
thank you kent
-------------------------------------------------------------------------------------
Hello Sir,
As the message you provided, it looks like either the hard disk drive is not
well connected or the hard drive is not recognized by the AEC7726H. Did you
just change another hard disk drive?! If yes, I guess the hard drive is
Seagate Barracuda 7200.8 series because it is not supported by the AEC7726H.
If not, please check the hardware connection again or provide me the detail
model name of the hard disk drive to check this issue.
Thanks for writing!
Your comments make our service improved.
ACARD Technical Support Dept.
FAE-Kent
Mail: ****@*****.com
Tel: 886(2)85122290 Ext: 3272
----- Original Message -----
From: "supportrc" <*********@****.acard.com>
Sent: Thursday, November 17, 2005 10:53 AM
Subject: <<9400083442>>Help! aec-7726H
>
>
> when i turn on my computer, screen is displaying scsi channel and ID.
> but, i can only see
> scsi channel :A id :1, scsi : null , capacity: 1MB, speed:80MB...........
>
> i have used for 2 years, this situation appeared 1 month ago.
>
> how can i fix it?
>
>
>
짧은글 일수록 신중하게.