¾Æ·¹Ä«¿¡¼­ ¾Ë·ÁÁØ staggerd spin-up Çϱâ.

À̹®Èì   
   Á¶È¸ 5653   Ãßõ 14    


Q10010406 - How can I enable staggered hard disk spin up on the Areca PCI series controllers?
  
ARC1XXX series SATA raid controller already support staggered power-up feature. It start first H/D about 8-20 second depends on M/B BIOS ( most of BIOS is about same time with first VGA bios screen show up ) then start other  H/D in step 0.4 sec. But staggered power-up feature must support byH/D & back-plane (specification by SATA II Phase one).You can check with H/D specification does it support staggered power-up or not. And you should check your H/D back-plane connector (7 pins sata signal + 15 pins power) does P11 pin (the 11's pin of 15 pins power) is pull-low , floating or pull-high. According to specification P11 pin must be floating or pull-high to support staggered power-up feature.
If you don't use any H/D back-plane, just use a simple 4-pin power to 15-pin translation power cable. This kind of cable will default tie-ground P11 pin. So you can't use staggered power-up feature.

Last update: 05:21 PM Thursday, November 10, 2005



³»¿ëÀ» º¸ÀÚ¸é
ÄÁÆ®·Ñ·¯¿Í Çϵ尡 µÑ´Ù staggerd spin-upÀ» Áö¿øÇÒ °æ¿ì,
ÆÄ¿ö ÄÉÀ̺íÀÌ ½ºÅÂ°Åµå ½ºÇɾ÷À» Áö¿øÇÏ´Â ¹éÇ÷¹Àο¡ ¿¬°áµÇ¾î Àְųª,
±×°ÍÀÌ ¾Æ´Ï¶ó¸é 15ÇÉ¿ë Àü¿ø ÄÉÀ̺íÀ» »ç¿ëÇؾ߸¸ ÇØ´ç ±â´ÉÀ» »ç¿ëÇÒ ¼ö ÀÖ´Ù°í Çϳ׿ä.
ÀÏ¹Ý 4ÇÉ Àü¿øÄÉÀ̺íÀº ¾ÈµÈ´Ù°í ÇÕ´Ï´Ù.





 
ªÀº±Û Àϼö·Ï ½ÅÁßÇÏ°Ô.


QnA
Á¦¸ñPage 4588/5687
2014-05   4997397   Á¤ÀºÁØ1
2015-12   1533294   ¹é¸Þ°¡
2010-11   8020   ÃÖÀμö
2011-06   8020   °­µÎÀÏ
2006-03   8020   ³²¼º·æ
2020-08   8021   Â÷³ÝÄÄÇ»ÅÍ
2004-02   8021   ±è¿ë¼ö
2004-04   8021   ÇϽÂÇù
2016-10   8021   witbox
2004-03   8021   Çѵ¿ÈÆ
2011-11   8021   Landa
2010-01   8021   ¼Õ°æÈ­
2010-10   8022   ¿¹°ü½Å±Ô½Ä
2020-06   8022   ¸®Àå´Ô
2004-03   8022   ½ÅÁø¿ì
2004-04   8022   ÇϽÂÇù
2011-04   8022   ÀÌÁ¾Çöoph
2015-01   8022   BJH
2010-04   8023   °­»óÂù
2011-02   8023   °­ÇѼº
2011-03   8023   Seean
2010-04   8024   ·¹Àκ¸¿ì7