Sun 3800 서버를 데탑에서 제어 하기 위해 하이퍼터미널로 접속하였는데요

파워전원만 켠 상태로 하이퍼터미널에 접속하니 서버를 테스트 한 이후 맨 아래 처럼 Input: 에서 커서만 깜막거리고 진행도 안돼고 명령어 입력도 안돼는 상황입니다.

서버의 LED는 모두 정상으로 표시되어 있구요.

명령어 입력이 되야 서버를 켤텐데 대략 난감입니다.
이상황이 어떤 상황인지 아시는 홴님 계시면 자세한 설명좀 부탁드리구요.

처리방법 좀 알려주세요~~

Hardware Reset...

@(#) SYSTEM CONTROLLER(SC) POST 19 2001/08/08 14:42
PSR = 0x044010e5
PCR = 0x04004000

        SelfTest running at DiagLevel:0x20

SC Boot PROM             Test
        BootPROM CheckSum               Test
IU        Test
        IU instruction set              Test
        Little endian access            Test
FPU       Test
        FPU instruction set             Test
SparcReferenceMMU     Test
        SRMMU TLB RAM                   Test
        SRMMU TLB Read miss             Test
        SRMMU page    probe             Test
        SRMMU segment probe             Test
        SRMMU region  probe             Test
        SRMMU context probe             Test
IIep Internal Cache     Test
        DCACHE RAM access               Test
        DCACHE TAG access               Test
        DCACHE Read miss                Test
        DCACHE Read hit                 Test
        DCACHE Write miss               Test
        DCACHE Write hit                Test
        ICACHE RAM access               Test
        ICACHE TAG access               Test
        ICACHE miss                     Test
        ICACHE hit                      Test
        ICACHE TAG flush                Test
PCIC      Test
        PCIC   Probe                    Test
        PCIC Config Register Access     Test
        PCI  Master Abort               Test
        PCIC Init                       Test
Memory    Test
        Memory Address                  Test
RIO Ebus      Test
        Rio Ebus Probe                  Test
RIO Ethernet  Test
        Rio Enet Probe                  Test
        Rio Ethernet Int Loopbacks      Test
DUART(16552) InterSC     Test
        Loopback                        Test
        COM3 port
        COM4 port
        Interrupt                       Test
        COM3 port       Intr #2

        COM4 port       Intr #2

System Clock      Test
        System Clock verify             Test
        Board0 Clock is selected
        75MHZ Fixed Crystal is the selected Clock Source
        CLK(Self) :0x0000ffff CLK(Other) : 0x00000000
        REF       : 0x0000222c
        CLOCK(SELF)   FREQ : 74.91 MHZ
        CLOCK(OTHER)  FREQ : 0.0 MHZ
SBBC PCI Controller      Test
        SBBC PCI Config Space probe     Test
        SBBC Internal Reg Access        Test
        SBBC Interrupts                 Test
        Port1 interrupt generation Tests  INTR #14

        Port0 interrupt generation Tests  INTR #14

SBBC Device0             Test
        PS Fail Reg(SBBC Dev0)          Test
SBBC Device1             Test
        SRAM (SBBC Dev1)                Test
        Memory Address Test (Non-destructive)
SBBC Device2             Test
        BId&MFG Reg (SBBC Dev2)         Test
SBBC Device3             Test
        FRU Prsnt Reg (SBBC Dev3)       Test
SBBC Device5             Test
        EPLD (SBBC Dev5)                Test
TOD(M48T59)              Test
        TOD Init                        Test
        TOD Functional                  Test
        TOD NVRAM(Non-Destructive)      Test
        TOD Interrupts                  Test
I2C Register Access      Test
        Enable Mux   Register           Test
        Channel Mux  Register           Test
        Add Command  Register           Test
        Data         Register           Test
Local I2C AT24C64     Test
        EEPROM       Device             Test
        performing eeprom sequential read

Local I2C PCF8591     Test
        VOLT_AD      Device             Test
        channel[00000001] Voltage(0x00000099) :1.49
        channel[00000002] Voltage(0x0000009B) :3.33
        channel[00000003] Voltage(0x00000099) :4.98
        channel[00000004] Voltage(0x00000000) :0.0
Local I2C LM75        Test
        TEMP0(IIep)  Device             Test
        Temparature : 47.0 Degree(C)

Local I2C LM75        Test
        TEMP1(Rio)   Device             Test
        Temparature : 38.50 Degree(C)

Local I2C LM75        Test
        TEMP2(CBH)   Device             Test
        Temparature : 55.50 Degree(C)

Local I2C PCF8574     Test
        Sc CSR       Device             Test
Console Bus Hub         Test
        CBH Register Access             Test
POST Complete.
ERI Device Present
Getting MAC address for SSC0
MAC address is 0:3:ba:d:82:d3
Hostname: eagle_tornado-sc
Address: 10.250.7.32
Netmask: 255.255.255.0
Attached TCP/IP interface to eri unit 0
Attaching interface lo0...done
Gateway: 10.250.7.1
Timeout waiting for network driver (flags=0x8062)

Adding 2854 symbols for standalone.

          Copyright 2001 Sun Microsystems, Inc.  All rights reserved.

Sun Fire 3800-6800 System Controller
RTOS version: 19
ScApp version: 5.12.5
SC POST diag level: min

The date is Saturday, June 12, 2010, 12:29:39 AM PDT.

Jun 12 00:29:40 eagle_tornado-sc Platform.SC: Boot: ScApp 5.12.5, RTOS 19
Jun 12 00:29:42 eagle_tornado-sc Platform.SC: SBBC Reset Reason(s): Power On Res
et
Jun 12 00:29:42 eagle_tornado-sc Platform.SC: Initializing the SC SRAM
Jun 12 00:29:45 eagle_tornado-sc Platform.SC: Clock Source: 75MHz
Jun 12 00:29:47 eagle_tornado-sc Platform.SC: Master System Controller
Jun 12 00:29:52 eagle_tornado-sc Platform.SC: Chassis is in dual partition mode.

Jun 12 00:29:52 eagle_tornado-sc Platform.SC: Cold boot detected: Configuring do
mains from NVCI
Domain: A keyswitch standby
Domain: C keyswitch standby
Jun 12 00:29:56 eagle_tornado-sc Platform.SC: NOTICE: FT0 has no grid power
Jun 12 00:29:57 eagle_tornado-sc Platform.SC: NOTICE: FT1 has no grid power
Jun 12 00:29:57 eagle_tornado-sc Platform.SC: NOTICE: FT2 has no grid power
Jun 12 00:29:57 eagle_tornado-sc Platform.SC: NOTICE: FT3 has no grid power

System Controller 'eagle_tornado-sc':

    Type  0  for Platform Shell

    Type  1  for domain A console
    Type  2  for domain B console
    Type  3  for domain C console
    Type  4  for domain D console

    Input:

Input: Jun 12 00:37:26 eagle_tornado-sc Platform.SC: Frame Manager monitorin
g is disabled, communication error