HP¼¹ö ¾î·¹ÀÌ°¡ ÀÌ»óÀÌ ÀÖ½À´Ï´Ù º¸½Ã°í Á¶¾ðÁ» ÇØÁÖ¼¼¿ä.
리빌딩후 잘 동작하는 줄 알았는데 오늘 보니 에러가 다시 났습니다.
아래 에러 로그 첨부하여 봄니다.
Array Diagnostic Utility Version 7.70.12.0
Array Diagnostic Utility Inspection Report Version 7.70.12.0
Date/Time: Sunday, January 06, 2013 10:20:53PM
Computer Model: HP Server
SLOT SUMMARY:
Slot Num Slot Type Array Controllers and Host Adapters Detected
-------- --------- --------------------------------------------
SLOT 1 PCI-E Smart Array P400 Controller
SLOT 1 Smart Array P400 Controller ERROR REPORT:
Logical drive 1 status = Interim recovery (volume functional, but not fault tolerant)
Port 2I, Box 1, Bay 2 failed - REPLACE (Mark bad operation failed)
Error occurred reading RIS copy from Port 2I, Box 1, Bay 2
SUBSYSTEM INFORMATION:
Chassis Serial Num: SGXXXXXXX
This Controller
Array Serial Number: PA2240MXXXXXX
Cache Serial Number: PA82C0HXXXXXX
Other Controller
Array Serial Number: Not Available
Cache Serial Number: Not Available
CONTROLLER IDENTIFICATION:
Configured Logical Drives: 1
Configuration Signature: 0xa617e671
Controller Firmware Rev: 2.08
Controller ROM Revision: 2.08
Controller Hardware Rev: 0x03
Boot Block Version: 0.02
Board ID: 0x3234103c
Cable or Config Error: 0x00 (No)
Invalid Host RAM Address: No
CPU Revision: 0x93
CPU to PCI ASIC Rev: 0x00
Cache Controller ASIC Rev: 0x00
PCI to Host ASIC Rev: 0x00
Marketing Revision: 0x44
Expand Disable Code: 0x01
Protocol Chip Count: 1
Enclosure Count: 3
Max SCSI IDs per Bus: 0
Big Drive Map: 0x0080 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Big Ext Drive Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Big Non-Disk Drive Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x1000
Fibre Chip Count: 0
Recovery ROM Inactive
Image Revision: 2.08
Recovery ROM Active Image
Flags Status: 0x01
Battery PIC Rev: 0xff
LOGICAL DRIVE IDENTIFICATION:
Logical Drive 1:
Sector Size: 512
Sectors Available: 143305920
Fault Tolerance Mode: Mirroring
Logical Param Table: cyl=17562 heads=255 sec/track=32 xlate sig=0x0
BIOS Disabled: No
LOGICAL DRIVE CONFIGURATION:
Logical Drive 1:
Configuration Signature: 0xabd33288
Mapping Scheme: Multiple Block
Physical Drives: 6 (number not valid after drive movement)
This Logical Drive: 2 (excluding spare drives)
Fault Tolerance Mode: Mirroring
Logical Param Table: cyl=17562 heads=255 sec/track=32 xlate sig=0x0
Distribution Factor: 256
Operating System: 64768
Controller Order: 0
Additional Information: 0
Offset to Data: 0
Int 13h Support Enabled: Yes
Sectors on Volume: 143305920
Sectors per Drive: 143305920
Big Drive Assignment Map: 0x00c0 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Big Spare Assignment Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Array Accelerator is enabled for this logical drive.
LOGICAL DRIVE STATUS:
Logical Drive 1:
Drive Status: Interim recovery (volume functional, but not fault tolerant)
Blocks to Rebuild: 0
Blocks Re-mapped:
Spare Status Flags: 0x00
Spare to Replaced Map: See Big Spare to Replace Map:
Media Was Exchanged: No
Cache Failure: No
Expand Failure: 0x00
Unit Flags: 0x02 (Write Error)
Big Remap Count: All Counts Zero
Big Drive Failure Map: 0x0040 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Big Replacement Drive Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Big Active Spare Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Big Spare to Replace Map: No spares have replaced any drives
Big Spare Marked OK Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
MONITOR AND PERFORMANCE DATA:
Port 2I, Box 1, Bay 2
Factory: Serial #, Firmware Rev, and Mfg/Model #:
20 20 4d 4c 30 30 30 30 34 39 33 35 00 00 00 00 ML00004935....
00 00 00 00 48 50 44 45 00 00 00 00 48 50 20 20 ....HPDE....HP
20 20 20 20 44 47 30 37 32 42 42 39 37 35 20 20 DG072BB975
20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............
00 00 00 00 ....
Since Power: Serial #, Firmware Rev, and Mfg/Model #:
20 20 4d 4c 30 30 30 30 34 39 33 35 00 00 00 00 ML00004935....
00 00 00 00 48 50 44 45 00 00 00 00 48 50 20 20 ....HPDE....HP
20 20 20 20 44 47 30 37 32 42 42 39 37 35 20 20 DG072BB975
20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............
00 00 00 00 ....
Serial Number Control: 0x0054
Firmware Revision Control: 0x0248
Mfg/Model Number Control: 0x0268
Factory Since Power Threshold Control
Serv. Time 00000614 00000001 00000000 2104
Read Blks 0000000019dd28fb 0000000000074177 0108
Hrd Read 0000c7ef 00000007 00000000 2104
Rtry Read 000003b4 00000000 00000000 2104
ECC Read 000000000000011b 0000000000000000 0000000000000000 2108
Write Blks 0000000009409d82 00000000000007b7 0108
Hrd Write 00000000 00000000 00000000 2104
Rtry Write 00000000 00000000 00000000 2104
Seeks 0000000000000000 0000000000000000 0808
Seek Errs 0000000000000000 0000000000000000 0000000000000000 0808
Spin Cyls 00000000 00000000 00000000 2104
Spin Time 0000 0000 0000 2202
Test 1 0000 0000 0000 0802
Test 2 0000 0000 0000 0802
Test 3 0000 0000 0000 0802
Test 4 0000 0000 0000 0802
Spare Blks ffffffff ffffffff 0a04
Re-mapped 00002496 00000000 00000000 2504
DRQ Tmots 0000 0000 0000 0802
Timeouts 0000 0000 0000 2102
Rebuilds 0001 0000 0000 2102
Spn Retrs ffff ffff 0000 2902
Fl Rd Recv 0000 0000 0000 2102
Fl Wt Recv 0005 0001 0000 2102
Format Err 0005 0001 0000 2102
POST Err 0000 0000 0000 0802
Drv Nt Ry 00000000 00000000 00000000 2104
Reallc Abt 00000000 00000000 00000000 0804
IRQ Gltchs 00000000 00000000 00000000 0804
Bus Flts 00000000 00000000 00000000 2104
Hot Plgs 00000003 00000000 00000000 2104
Tk Rwt Err ffff ffff 0000 2902
Rmp Wt Err 0000 0000 0000 2102
Bg Fw Rev 0000000000000000 0000000000000000 0848
Med Flrs 0000 0000 0000 2102
Hrdw Errs 000f 0003 0000 2102
Abt Cmd Fl 0000 0000 0000 2102
Spn Up Fl 0000 0000 0000 2102
Bd Tgt Cnt 0000 0000 0000 2102
Pred Fails 0000007e 00000001 00000000 2104
DRIVE ERROR LOG:
Error Log Header:
Parameter Length = 0x14
Entry Size = 0x0040
Current Entry = 0x0f
Total Errors Logged = 0x000028cf
Error Log Data:
SCSI CAM Sense Sense
Stat Stat Key Code Qual Block(Vl) Time Op Info
---- ---- ----- ----- ---- --------- ---- -- ----
00 02 00 00 00 0010e2e0(0) 00000613 2a 0000
00 02 00 00 00 00292038(0) 00000613 2a 0000
00 02 00 00 00 0010e2e0(0) 00000613 2a 0000
00 02 00 00 00 0028d150(0) 00000613 2a 0000
00 02 00 00 00 00292038(0) 00000613 2a 0000
00 02 00 00 00 0028d150(0) 00000613 2a 0000
02 04 05 24 00 00000000(0) 00000613 12 0000
02 04 06 29 02 00000000(0) 00000613 00 0000
02 04 05 24 00 00000000(0) 00000613 12 0000
02 04 06 29 02 00000000(0) 00000613 00 0000
02 04 05 24 00 00000000(0) 00000613 12 0000
02 04 06 29 02 00000000(0) 00000613 00 0000
02 04 05 24 00 00000000(0) 00000613 12 0000
02 04 03 11 01 00073f2e(1) 00000613 28 0000
02 04 04 32 00 00000000(0) 00000614 07 0000
02 04 06 29 02 00000000(0) 000005f8 00 0000
02 04 05 24 00 00000000(0) 000005f8 12 0000
02 04 06 29 02 00000000(0) 000005f8 00 0000
02 04 05 24 00 00000000(0) 000005f8 12 0000
02 04 06 29 02 00000000(0) 00000613 00 0000
Port 2I, Box 1, Bay 1
Factory: Serial #, Firmware Rev, and Mfg/Model #:
33 4e 50 30 44 34 44 59 30 30 30 30 39 37 33 32 3NP0D4DY00009732
4e 5a 34 36 48 50 44 35 00 00 00 00 48 50 20 20 NZ46HPD5....HP
20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20 DG072ABAB3
20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............
00 00 00 00 ....
Since Power: Serial #, Firmware Rev, and Mfg/Model #:
33 4e 50 30 44 34 44 59 30 30 30 30 39 37 33 32 3NP0D4DY00009732
4e 5a 34 36 48 50 44 35 00 00 00 00 48 50 20 20 NZ46HPD5....HP
20 20 20 20 44 47 30 37 32 41 42 41 42 33 20 20 DG072ABAB3
20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............
00 00 00 00 ....
Serial Number Control: 0x0054
Firmware Revision Control: 0x0248
Mfg/Model Number Control: 0x0268
Factory Since Power Threshold Control
Serv. Time 0025c738 0000000a 00000000 2104
Read Blks 000001fe32d4050f 00000000000f8843 0108
Hrd Read 00000000 00000000 00000000 2104
Rtry Read 00000000 00000000 00000000 2104
ECC Read 0000000000000000 0000000000000000 0000000000000000 2108
Write Blks 000000009b76be69 0000000000012475 0108
Hrd Write 00000000 00000000 00000000 2104
Rtry Write 00000000 00000000 00000000 2104
Seeks 0000000000000000 0000000000000000 0808
Seek Errs 0000000000000000 0000000000000000 0000000000000000 0808
Spin Cyls 00000000 00000000 00000000 2104
Spin Time 0000 0000 0000 2202
Test 1 0000 0000 0000 0802
Test 2 0000 0000 0000 0802
Test 3 0000 0000 0000 0802
Test 4 0000 0000 0000 0802
Spare Blks ffffffff ffffffff 0a04
Re-mapped 00000000 00000000 00000000 2504
DRQ Tmots 0000 0000 0000 0802
Timeouts 0000 0000 0000 2102
Rebuilds 0000 0000 0000 2102
Spn Retrs ffff ffff 0000 2902
Fl Rd Recv 0000 0000 0000 2102
Fl Wt Recv 0000 0000 0000 2102
Format Err 0000 0000 0000 2102
POST Err 0000 0000 0000 0802
Drv Nt Ry 00000000 00000000 00000000 2104
Reallc Abt 00000000 00000000 00000000 0804
IRQ Gltchs 00000000 00000000 00000000 0804
Bus Flts 00000000 00000000 00000000 2104
Hot Plgs 00000000 00000000 00000000 2104
Tk Rwt Err ffff ffff 0000 2902
Rmp Wt Err 0000 0000 0000 2102
Bg Fw Rev 0000000000000000 0000000000000000 0848
Med Flrs 0000 0000 0000 2102
Hrdw Errs 0000 0000 0000 2102
Abt Cmd Fl 0000 0000 0000 2102
Spn Up Fl 0000 0000 0000 2102
Bd Tgt Cnt 0000 0000 0000 2102
Pred Fails 00000000 00000000 00000000 2104
DRIVE ERROR LOG:
Error Log Header:
Parameter Length = 0x14
Entry Size = 0x0040
Current Entry = 0x1d
Total Errors Logged = 0x0000005d
Error Log Data:
SCSI CAM Sense Sense
Stat Stat Key Code Qual Block(Vl) Time Op Info
---- ---- ----- ----- ---- --------- ---- -- ----
02 04 06 29 02 00000000(0) 0016fde8 00 0000
02 04 06 29 02 00000000(0) 00178ce3 00 0000
02 04 06 29 02 00000000(0) 0019978e 00 0000
02 04 06 29 02 00000000(0) 0019b475 00 0000
02 04 06 29 02 00000000(0) 001a038a 00 0000
02 04 06 29 02 00000000(0) 001c15be 00 0000
02 04 06 29 02 00000000(0) 001db553 00 0000
02 04 06 29 02 00000000(0) 001e6368 00 0000
02 04 06 29 02 00000000(0) 001e63de 00 0000
02 04 06 29 02 00000000(0) 001f9db9 00 0000
02 04 06 29 02 00000000(0) 001fbe4e 00 0000
02 04 06 29 02 00000000(0) 0020b6ff 00 0000
02 04 06 29 02 00000000(0) 00214e0c 00 0000
02 04 06 29 02 00000000(0) 0021b7fb 00 0000
02 04 06 29 02 00000000(0) 0021d890 00 0000
02 04 06 29 02 00000000(0) 002223ea 00 0000
02 04 06 29 02 00000000(0) 002271f7 00 0000
02 04 06 29 02 00000000(0) 0022864c 00 0000
02 04 06 29 02 00000000(0) 0022d81a 00 0000
02 04 06 29 02 00000000(0) 0022dd42 00 0000
SURFACE ANALYSIS STATUS:
Time remaining to start: 14 secs.
Surface analysis delay: 15 secs.
Enclosure 1:
Big
Drive ID Current Block
-------- -------------
00 0x00000000
01 0x00000000
02 0x00000000
03 0x00000000
04 0x00000000
05 0x00000000
06 0x00073f00
07 0x00073f00
08 0x00000000
09 0x00000000
10 0x00000000
11 0x00000000
12 0x00000000
13 0x00000000
14 0x00000000
15 0x00000000
Enclosure 2:
Big
Drive ID Current Block
-------- -------------
00 0x00000000
01 0x00000000
02 0x00000000
03 0x00000000
04 0x00000000
05 0x00000000
06 0x00000000
07 0x00000000
08 0x00000000
09 0x00000000
10 0x00000000
11 0x00000000
12 0x00000000
13 0x00000000
14 0x00000000
15 0x00000000
Enclosure 3:
Big
Drive ID Current Block
-------- -------------
00 0x00000000
01 0x00000000
02 0x00000000
03 0x00000000
04 0x00000000
05 0x00000000
06 0x00000000
07 0x00000000
08 0x00000000
09 0x00000000
10 0x00000000
11 0x00000000
12 0x00000000
13 0x00000000
14 0x00000000
15 0x00000000
Big Surface Surface
Logical Big Inconsistent Blocks Controller Analysis Analysis
Drive Status Block Reassigned Resets Passes Pass Time
------- ------ ------------ ---------- ---------- ---------- ----------
1 0x03 0x00000000 18560 4 15237 5271
2 0x00 0x00000000 0 0 0 0
3 0x00 0x00000000 0 0 0 0
4 0x00 0x00000000 0 0 0 0
5 0x00 0x00000000 0 0 0 0
6 0x00 0x00000000 0 0 0 0
7 0x00 0x00000000 0 0 0 0
8 0x00 0x00000000 0 0 0 0
9 0x00 0x00000000 0 0 0 0
10 0x00 0x00000000 0 0 0 0
11 0x00 0x00000000 0 0 0 0
12 0x00 0x00000000 0 0 0 0
13 0x00 0x00000000 0 0 0 0
14 0x00 0x00000000 0 0 0 0
15 0x00 0x00000000 0 0 0 0
16 0x00 0x00000000 0 0 0 0
17 0x00 0x00000000 0 0 0 0
18 0x00 0x00000000 0 0 0 0
19 0x00 0x00000000 0 0 0 0
20 0x00 0x00000000 0 0 0 0
21 0x00 0x00000000 0 0 0 0
22 0x00 0x00000000 0 0 0 0
23 0x00 0x00000000 0 0 0 0
24 0x00 0x00000000 0 0 0 0
25 0x00 0x00000000 0 0 0 0
26 0x00 0x00000000 0 0 0 0
27 0x00 0x00000000 0 0 0 0
28 0x00 0x00000000 0 0 0 0
29 0x00 0x00000000 0 0 0 0
30 0x00 0x00000000 0 0 0 0
31 0x00 0x00000000 0 0 0 0
32 0x00 0x00000000 0 0 0 0
ACCELERATOR STATUS:
Logical Drive Disable Map: 0xfffffffe
Read Cache Size: 208 MBytes
Posted Write Size: 0 MBytes
Disable Flag: 0x00
Status: 0x00000001
Disable Code: 0x0000
Total Memory Size: 256 MBytes
Battery Count: 0
Battery Status: 0x0000
Parity Read Errors: 0000
Parity Write Errors: 0000
Error Log: N/A
Failed Batteries: 0x0000
Board Present: Yes
Accelerator Failure Map: 0x00000000
Max Error Log Entries: 12
NVRAM Load Status: 0x00
Memory Size Shift Factor: 0x0a
Non Battery Backed Memory: 208 MBytes
Memory State: 0x00
PHYSICAL DRIVE IDENTIFICATION:
Port 2I, Box 1, Bay 2
Drive Model: HP DG072BB975
Product Rev: HPDE
Serial Number: ML00004935
WWID: 0x5001afc07d3c2d02000000000000000000000000
Drive Type: 0x02 SAS
Block Size: 512 bytes/sector
Total Blocks: 143374738 sectors/disk
Reserved Blocks: 65536 reserved sectors/disk
SCSI Inquiry Bits: 0x02
Stamped for M&P: yes
Last Failure Reason: 0x05 (Mark bad operation failed)
Phys Drive Flags: 0x00 0x2b 0xe0 0x00
S.M.A.R.T. Supported
S.M.A.R.T. Disabled
Configured as part of Logical Drive
Drive write cache is currently enabled
Drive write cache setting is changeable and safe
Physical Connector: 2I (controller connector attached to drive)
Physical Box on Bus: 1 (number of the physical enclosure in which drive resides)
Physical Bay in Box: 2 (number of the physical drive bay in the enclosure)
Port 2I, Box 1, Bay 1
Vendor Id: HP
Product Id: DG072ABAB3
Product Rev: HPD5
Vendor Specific: 3NP0D4DY
Serial Number: 3NP0D4DY00009732NZ46
SCSI Inquiry Header: 00 00 05 12 8b 00 00 02
Device Supports: Tagged Command Queueing
Drive Type: 0x02 SAS
Block Size: 512 bytes/sector
Total Blocks: 143374738 sectors/disk
Reserved Blocks: 65536 reserved sectors/disk
SCSI Inquiry Bits: 0x02
Stamped for M&P: yes
Last Failure Reason: 0x00 (Drive has not failed)
Phys Drive Flags: 0x01 0x25 0xa0 0x00
Drive present and operational
S.M.A.R.T. Supported
S.M.A.R.T. Enabled
Configured as part of Logical Drive
Drive write cache is currently disabled
Drive write cache setting is changeable and safe
Physical Connector: 2I (controller connector attached to drive)
Physical Box on Bus: 1 (number of the physical enclosure in which drive resides)
Physical Bay in Box: 1 (number of the physical drive bay in the enclosure)
MODE SENSE:
Header: 00 de 00 10 00 00 00 08 00 00 00 00 00 00 02 00
Page 01: 81 0a e4 0b ff 00 00 00 05 00 ff ff
Page 02: 82 0e 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Page 03: 83 16 0f 1e 00 00 00 0e 00 00 03 03 02 00 00 01
00 6c 00 4e 40 00 00 00
Page 04: 84 16 01 08 fc 02 00 00 00 00 00 00 00 00 00 00
00 00 00 00 27 31 00 00
Page 07: 87 0a 04 0b ff 00 00 00 00 00 ff ff
Page 08: 88 12 10 00 ff ff 00 00 ff ff ff ff 00 20 00 00
00 00 00 00
Page 09: 89 0e 0c 00 00 00 00 00 00 00 00 00 00 00 00 00
Page 0a: 8a 0a 00 10 00 00 00 00 00 00 04 2e
Page 0c: 8c 16 c0 00 00 0f 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 10 08
Page 18: 98 06 06 00 00 00 00 00
Page 19: 99 06 26 00 07 d0 00 00
Page 1a: 9a 0a 00 00 00 00 00 05 00 00 00 04
Page 1c: 9c 0a 11 04 00 00 0b b8 00 00 00 02
Page 00: 80 06 00 00 0f 00 00 00
CONTROLLER PARAMETERS:
LED Control: 0x00
Command List Verification: On
Backed-out Write drives: 0
Stripes for Parity: 0
Distribution Mode: 0x00
Maximum Driver Requests: 0xffff
Elevator Trend Count: 0x0032
Disable Elevator: 0x00
Force Scan Complete: 0x00
Synch/Asynch Mode: Auto Detect
Force Narrow: No
Rebuild Priority: 64
Expand Priority: 64
SDB ASIC Fix: 0x00
PDIP Burst Disable: 0x00
Software Name:
Hardware Name:
Enclosure 1 PARAMETERS:
Inquiry Data Valid: No
Hot Plug Counts:
All counts are zero
Fan Alert Count: 0x0000
Alarm Status: 0x00 (No Alarms)
Temperature Status: 0x00
Valid Alarm Bits: 0x00
Alarm Count: 0000
Specific Counts: 00000 00000 00000 00000 00000 00000 00000 00000
Connection Info: 0x0002
SCSI Device Rev: 0x03
Fan Status: 0x0000
More Inquiry Data:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
SCSI Device Type: 0x3230103c (unknown)
Interrupt Count: 00000000
Ultra Bus Faults: 0x00000000
SCSI Initiator ID: 0
SCSI Target ID: 0
Chassis Serial Number: Not Available
Physical Connector: 1I (controller connector attached to drive)
Big Inst Drive Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Big Bus Map: 0x000f 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
More Connection Info: 0x00 (Single-Ended SCSI bus enabled)
Extended Powersupply / Fan Information not available on this unit
Enclosure 2 PARAMETERS:
Inquiry Data Valid: No
Hot Plug Counts:
All counts are zero
Fan Alert Count: 0x0000
Alarm Status: 0x00 (No Alarms)
Temperature Status: 0x00
Valid Alarm Bits: 0x00
Alarm Count: 0000
Specific Counts: 00000 00000 00000 00000 00000 00000 00000 00000
Connection Info: 0x0002
SCSI Device Rev: 0x03
Fan Status: 0x0000
More Inquiry Data:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
SCSI Device Type: 0x3230103c (unknown)
Interrupt Count: 00000000
Ultra Bus Faults: 0x00000000
SCSI Initiator ID: 0
SCSI Target ID: 0
Chassis Serial Number: Not Available
Physical Connector: 2I (controller connector attached to drive)
Big Inst Drive Map: 0x0080 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Big Bus Map: 0x00f0 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
More Connection Info: 0x00 (Single-Ended SCSI bus enabled)
Fans Reporting Extended Information: 2
Fan 1 : OK
Fan 2 : OK
Powersupplies Reporting Extended Information: 0
Enclosure 3 PARAMETERS:
Inquiry Data Valid: No
Hot Plug Counts:
All counts are zero
Fan Alert Count: 0x0000
Alarm Status: 0x00 (No Alarms)
Temperature Status: 0x00
Valid Alarm Bits: 0x00
Alarm Count: 0000
Specific Counts: 00000 00000 00000 00000 00000 00000 00000 00000
Connection Info: 0x0000
SCSI Device Rev: 0x00
Fan Status: 0x0000
More Inquiry Data:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
SCSI Device Type: 0x00000000 (unknown)
Interrupt Count: 00000000
Ultra Bus Faults: 0x00000000
SCSI Initiator ID: 0
SCSI Target ID: 0
Chassis Serial Number: Not Available
Physical Connector: 0x0000 (controller connector attached to drive)
Big Inst Drive Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Big Bus Map: 0x0000 0x0000 0x0000
Àú·¸°Ô ¾î´Àµð½ºÅ© ¿¡·¯¶ó°í º¸°í¼ ³ª¿ÍÁÖ¸é Á¤¸» °í¸¶¿î°ÅÁÒ. ÄÜÆ®·Ñ·¯±îÁö Çà°É·Á¼ ¸®ºÎÆÃµÇ¸é ¿¡·¯·Î±×µµ ¸øÂï°í ¹¹°¡ ¹®Á¦ÀÎÁö ¸ð¸£´Ù°¡ ¹ß¸¸ µ¿µ¿ ±¸¸£´ÂÀÏÀÌ ºñÀϺñÀç ÇÕ´Ï´Ù.
ÀÏ´Ü ±³Ã¼ÇÑ Çϵ忴´Âµ¥ »õ Çϵ忴½À´Ï´Ù. ÇÑ´Þµµ ¾ÈµÇ¼ Àú·¯³»¿ä...
ÀÏ´Ü ÇØ´ç ¼¹ö´Â ´Ù¿î ½ÃÄÑ ³õ¾Ò½À´Ï´Ù.
ÇÏµå ±³Ã¼ÈÄ Àç°¡µ¿ÇÒ·Á°í ÇÕ´Ï´Ù.