½Ã½ºÄÚ ÄÁÆ®·Ñ·¯Çü AP ¸¦ ´Üµ¶ÇüÀ¸·Î

   Á¶È¸ 7565   Ãßõ 0    



도움을 청할곳이 이곳밖에 없이 도움 요청드립니다.


시스코 AIR-AP1242AG-K-K9 입니다.

현재설정이 컨트롤러형으로 돼있어 단독형 펌웨어(IOS)를 구하고 있습니다.

콘솔로 설정할려고 해도 설정을 할 수가 없어서요.


밑에 댓글 보충사진입니다. 모드버튼을 20초 누른 이후에 콘솔에 이런 화면이 나옵니다.





TFTP서버에서 전송이 시작됩니다.

삶이 그대를 속일지라도~~
ªÀº±Û Àϼö·Ï ½ÅÁßÇÏ°Ô.
ºí·¢ÆÞ 2020-12
±¸±Û·Î °Ë»öÇϸé Æß¿þ¾î ±¸ÇÒ¼ö ÀÖÀ»°Ì´Ï´Ù.
3700i ¸¦ ±¸±Û¿¡¼­ °Ë»öÇÏ¿© ´Ù¿î¹Þ¾Æ¼­ ´Üµ¶ÇüÀ¸·Î ¹Ù…f½À´Ï´Ù
     
±¸±Û¿¡¼­ ¾È³ª¿À´õ¶ó±¸¿ä, ½Ã½ºÄÚȨÇÇ¿¡¼­´Â ·Î±×ÀÎÇ϶ó°í ÇÏ°í ¤¾¤¾
¹Ú¹®Çü 2020-12
¿¾³¯ °ÍÀÌÁö¸¸ ÂÊÁö·Î µå·È½À´Ï´Ù..
     
°¨»çÇÕ´Ï´Ù. Çѹø Çغ¸°Ú½À´Ï´Ù.^^
Á¦°¡ ¸îÀÏ°£ ÇØ¿Â ½ÇÆб⸦ ¿Ã¸®°Ú½À´Ï´Ù.
¹®Á¦) ºñ¹Ð¹øÈ£°¡ °É·ÁÀÖ´Â ap1242ag¸¦ ±¸¸Å
½Ãµµ) ÀÎÅͳÝÀ» ã¾Æº¸´Ï ¸®¼Â¹æ¹ý°ú ¼³Á¤¹æ¹ýÀÌ ³ª¿Í ÀÖ¾ú½À´Ï´Ù.

¸®¼Â¹æ¹ý) ½Ã½ºÄÚ AP ÃʱâÈ­(¸®¼Â¹öÆ° 20ÃÊ)ÈÄ IP ¼³Á¤(¸ðµå¹öÆ°À» ´©¸¥»óÅ¿¡¼­ Àü¿øÀΰ¡ÇÕ´Ï´Ù.)

1. ÃʱâÈ­ ÈÄ ÄܼÖÆ÷Æ®·Î Á¢¼Ó(È£½ºÆ® À̸§ º¯°æ, IP¼¼ÆÃ, µðÆúÆ® °ÔÀÌÆ®¿þ¿¡ ¼¼ÆÃ)<- ÄܼÖÆ÷Æ®·Î Á¢¼ÓÇϱâÀ§Çؼ­´Â 9ÇÉ(½Ã¸®¾óÆ÷Æ®) RJ45ÄÉÀ̺í ÇÊ¿äÇϸç,
                                                                                                                          Á¢¼ÓÇÁ·Î±×·¥Àº Putty ÀÔ´Ï´Ù.
  AP>enable            <- ÃʱâÈ­¸éÀÌ AP> ÀÌ ³ª¿Í¾ß ÇÕ´Ï´Ù. AP0024.5e04.db7e> ÀÌ·±½ÄÀ¸·Î ³ª¿À¸é ¾Æ·¡ÀÇ ³»¿ëµéÀÌ ÁøÇàÀÌ ¾ÈµË´Ï´Ù. Áï, AP>Àº µ¶¸³ÇüÀÌ¸ç  AP0024.5e04.db7e> Àº ÄÜÆ®·Ñ·¯ÇüÀ¸·Î Æß¿þ¾î(IOS)ÀÇ º¯È¯ÀÌ ÇÊ¿äÇÕ´Ï´Ù.
  Password: Cisco    <--- ÃʱâÆнº¿öµå
  AP#configure terminal
  AP(config)#hostname test <-È£½ºÆ® À̸§ º¯°æ
  test(config)#interface bvi 1
  test(config-if)#ip address 100.100.103.230 255.255.255.0 <--IP, ¼­ºê³Ý¸¶½ºÅ©)
  test(config-if)#no shutdown <- ÀÎÅÍÆäÀ̽º È°¼ºÈ­
  test(config-if)#exit
  test(config-if)#wr  <--- ¼³Á¤ ÀúÀå
  test(config)#ip default-gateway 100.100.103.1 <- µðÆúÆ® °ÔÀÌÆ®¿þÀÌ ¼³Á¤
  test(config)#end
2. 100.100.103.230  HTTP·Î Á¢¼ÓÈÄ Ãß°¡ ¼ÂÆÃ
3. ¹«¼±·£ ÀÎÅÍÆäÀ̽º È°¼ºÈ­(2¹ø À¥Á¢¼ÓÀ¸·Îµµ ¼³Á¤ °¡´É)
  test#configure terminal
  test(config)#int dot11radio 0
  test(config-if)#no shutdown
  test(config-if)#exit
  test(config)#int dot11radio 1
  test(config-if)#no shutdown
  test(config-if)#exit
  test(config)#wr  <--- ¼³Á¤ ÀúÀå
AP> »óÅÂ(µ¶¸³Çü)¸¦ ¸¸µé¾î¾ß¸¸ ³ª¸ÓÁö ¼³Á¤ÀÌ °¡´ÉÇϱ⿡ µ¶¸³ÇüÆß¿þ¾î·Î ¹Ù²Ù´Â ¹æ¹ýÀ» ¾Ë¾ÆºÃ½À´Ï´Ù.
Áغñ¹°) Æß¿þ¾î(c1240-k9w7-tar.124-25d.JA2.tar / c1240-k9w8-tar.124-25e.JAO5.tar µÎ°³ÀÇ Æß¿þ¾î¸¦ ¹Ú¹®Çü´Ô²²¼­ º¸³»Áּ̽À´Ï´Ù. °¨»çÇÕ´Ï´Ù.^^
          ÀÌ µÎ°³Áß k9w7Àº µ¶¸³ÇüÆß¿þ¾î, k9w8Àº ÄÁÆ®·Ñ·¯Çü Æß¿þ¾îÀÔ´Ï´Ù.), tftp¼­¹ö(tftpd32 ÇÁ·Î±×·¥»ç¿ë), putty ÇÁ·Î±×·¥, Äֿܼ¬°áÄÉÀ̺í(9ÇÉ-RJ45)
1. Àü¿øÀ» ²ö»óÅ¿¡¼­ ¸ðµå¹öÆ°À» ´©¸£°í Àü¿øÀ» Àΰ¡ÇÕ´Ï´Ù.(20ÃÊÈÄ¿¡ Áö½Ãµî°ú ÄÉÀÌºí¿¬°áµîÀÌ µÎ°³´Ù »¡°£ºÒÀÌ µé¾î¿À¸é ¼ÕÀ» ¶Á´Ï´Ù.)
2. À§ º»¹® »çÁø°ú °°Àº »óÅ°¡ ÄַܼΠº¸À̸鼭, TFTP¼­¹ö¿¡¼­ Æß¿þ¾îÈ­ÀÏÀ» Àü¼ÛÇÕ´Ï´Ù.
3. ³ª¸ÓÁö´Â ¾Ë¾Æ¼­ Æß¿þ¾î ¾÷±×·¹À̵åÇÕ´Ï´Ù. ´ÙÇÏ°í ³ª¸é AP> »óÅ°¡ µË´Ï´Ù.(ÀÌ°ÍÀÌ Á¤»óÀûÀÎ Æß¿þ¾î ¹æ¹ýÀÔ´Ï´Ù.)

2¹øº¸Ãæ. Æß¿þ¾î È­ÀÏÀÌ ÀÚµ¿À¸·Î Àü¼ÛµÇ±â À§Çؼ­´Â È­ÀÏÀ̸§À» c1240-k9w7-tar.124-25d.JA2.tar -> c1240-k9w7-tar.default ·Î º¯È¯½ÃÄÑÁà¾ßÇÕ´Ï´Ù. ¶ÇÇÑ TFTP¼­¹ö ¼³Á¤À» ÇØÁà¾ßÇϴµ¥, PC ³×Æ®¿öÅ©¾Æ´äÅÍÀÇ IP¸¦ 10.0.0.1 / ¼­ºê³×Æ®¿öÅ© 255,255,255,0 À¸·Î ¼³Á¤ÇؾßÇÕ´Ï´Ù.
±×¸®°í ¹æÈ­º®¼³Á¤À» ²¨¾ßÇÕ´Ï´Ù. ÄÉÀÌºí¿¬°áÀº AP Äֿܼ¡ RJ45- PC¿¡ 9Çɽø®¾óÆ÷Æ® ¿¬°á(ÀÌ°ÍÀº PUTTYÇÁ·Î±×·¥½ÇÇà), AP ethernet¿¡
RJ45¿¬°á-PC ethernet¿¡ RJ45¿¬°á(Å©·Î½ºÄÉÀÌºí »ç¿ëÇÏ¿´½À´Ï´Ù. ÀÌ°ÍÀº TFTP32 ÇÁ·Î±×·¥½ÇÇà)

ÀÌ·¸°Ô Çߴµ¥, Àü¼Û¿¡·¯°¡ ¶ß¸é¼­ ¾ÈµÇ¾ú½À´Ï´Ù.
Reverting to a Previous Release Using the MODE Button and a TFTP Server Procedure
Step 1
Configure the PC on which your TFTP server software runs with a static IP address in the range of 10.0.0.2 to 10.0.0.30.
Step 2
Make sure that the PC contains the access point image file (such as ap3g2-k9w7-tar.152-4.JB4.tar for a 2700 or 3700 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3
Rename the access point image file in the TFTP server folder to ap3g2-k9w7-tar.default for a 2700 or a 3700 series access point.
Step 4
Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5
Disconnect power from the access point.
Step 6
Press and hold the MODE button while you reconnect power to the access point.
Note
The MODE button on the access point must be enabled.
Step 7
Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the MODE button.
Step 8
Wait until the access point reboots as indicated by all the LEDs turning green followed by the Status LED blinking green.
Step 9
After the access point reboots, reconfigure the access point using the GUI or the CLI.
¹Ú¹®Çü 2020-12
Àú´Â À©µµ¿ìÁî¿¡¼­  RS-232C Å͹̳ηΠ¾÷µ¥ÀÌÆ® Çß´ø °ÍÀ¸·Î ±â¾ïÇÕ´Ï´Ù..

Àß ¾Æ½Ç ¼ö µµ ÀÖ°ÚÁö¸¸ ±¸±Û¸µ ÇÏ½Ã¸é ¸Å´º¾óÀÌ ¸¹ÀÌ ³ª¿É´Ï´Ù..
     
TFTP¼­¹ö ÁÖ¼Ò¸¦ 10.0.0.5 ·Î ÇÏ´Ï Àü¼ÛÀÌ µÇ¾î¼­ ÇØ°áµÇ¾ú½À´Ï´Ù.^^ ³ª¸ÓÁö´Â ¼ú~ ¼ú~ °¨»çÇÕ´Ï´Ù.

Configure the PC on which your TFTP server software runs with a static IP address in the range of 10.0.0.2 to 10.0.0.30.

10.0.0.1 ·Î ¼³Á¤ÇÏ¿©¼­ ¾ÈµÇ¾ú´ø °Å³×¿ä. ÀÎÅͳݰ˻öÀ» ÇßÀ»¶§, 10.0.0.1 ·Î Ç϶ó°í µÇ¾îÀÖ¾ú°í, AP ºÎÆÃÇÒ¶§ º¸´Ï±î ÀÚü IP°¡ 10.0.0.1 À̾

µ¿ÀÏÇÏ°Ô ¼ÂÆÃÇÏ´Â Áپ˾Ҵµ¥, »ý°¢Çغ¸´Ï APÀÇ IP °¡ 10.0.0.1 ÀÌ´Ï±î ´Ù¸¥ ¾ÆÀÌÇÇ ÁÖ¼Ò 10.0.0.x ÀÇ ÁÖ¼Ò¸¦ ½áÁà¾ß Çß´ø°Í °°½À´Ï´Ù.


QnA
Á¦¸ñPage 3709/5689
2015-12   1546604   ¹é¸Þ°¡
2014-05   5010937   Á¤ÀºÁØ1
01-18   1999   epowergate
2016-04   4623   Macstall
01-25   2029   osthek83
2011-03   12454   ÀÌÁöÆ÷Åä
2018-07   2988   ¼ÛÁøÇö
2020-12   7566   Áø¾È¸¶ÀÌ»ê
2019-09   2446   ºí·ç½ºÄ«ÀÌ
2022-06   1816   À¯È£ÁØ
2022-06   1403   ¾ÖÈ£¹Ú
02-01   2415   ¹¹µçÆȾƿä
2015-03   4218   ½ÅÀº¿Ö
2017-04   6227   Carolus
2018-07   12951   ÇÁ·Î½Ã¾Æ
2015-03   4410   ºí·ç¿µ»ó
2020-12   3309   »ç¶ûÇ϶ó
2020-12   2936   ÀÛÀº°¡¿À¸®
2013-11   25576   ¼¼°¡»õÅÏ
2016-05   5046   ³ªÆÄÀÌ°­½ÂÈÆ
2020-12   2077   Sikieiki
2013-11   6987   °æ¹ÚÇѽùÎ