HP ProLiant 100 Series servers
To enable the controller and set boot order:
1. Power up the server.
2. When prompted during the start-up sequence, access RBSU by pressing the F10 key.
3. Select Advanced or Advanced Settings.
4. Select SATA Configuration or Hard Drive Configuration.
5. Change SATA #1 to RAID.
6. Return to the previous screen by pressing the Escape key.
7. Select the Boot Menu by pressing the right arrow key.
8. Select Hard Disk Drives.
9. To assign the HP Smart Array B110i SATA RAID Controller as the boot controller, set Ctrl 1 to HP
Smart Array B110i SATA RAID Controller.
10. Press the F10 key to save the setting and to exit RBSU.
HP ProLiant 300 Series servers
To enable the controller and set boot order:
1. Power up the server.
2. When prompted during the start-up sequence, access RBSU by pressing the F9 key.
3. Select Advanced Settings.
4. Select Embedded SATA RAID.
5. Select Enabled.
6. Return to the previous screen by pressing the Escape key.
7. Select Boot Controller Order.
8. To assign the HP Smart Array B110i SATA RAID Controller as the boot controller, set Ctrl 1 to HP
Smart Array B110i SATA RAID Controller.
9. Press the F10 key to save the settings and to exit RBSU
설정하셨으면 다음 부팅부터 RAID컨트롤러가 동작합니다.
포스팅 후 ORCA(Option ROM Configuration for Arrays)들어가셔서 Logical Drive를 잡으시면 됩니다.
다음은 동일 메뉴얼 6페이지 내용입니다.
To create a logical drive using ORCA:
1. Power up the server.
2. When prompted during the start-up sequence, access ORCA by pressing the F8 key.
3. Select Create Logical Drive.
The screen displays a list of all unconfigured physical drives and the valid RAID options for the
system.
4. Use the Arrow keys, Spacebar, and Tab key to navigate around the screen and set up the logical
drive, including an online spare drive, if one is required.
NOTE: You cannot use ORCA to configure one spare drive to be shared among several
arrays. Only ACU enables you to configure shared spare drives.
5. Press the Enter key to accept the settings.
Enabling and configuring the controller 7
6. Press the F8 key to confirm the settings and save the new configuration.
After several seconds, the Configuration Saved screen appears.
7. Press the Enter key to continue.
Repeat this procedure to create additional logical drives.
만약 POST후 F8키를 통한 ORCA진입이 안된다면 다시 RBSU에 진입하셔서 레이드컨트롤러를 부팅컨트롤러로 제대로 잡아놓았는지 확인해보시기 바랍니다.
HP의 B110i 메뉴얼입니다.
POST 후 RBSU 진입방법 나와있습니다.
메뉴얼 페이지 5의 내용입니다.
HP ProLiant 100 Series servers
To enable the controller and set boot order:
1. Power up the server.
2. When prompted during the start-up sequence, access RBSU by pressing the F10 key.
3. Select Advanced or Advanced Settings.
4. Select SATA Configuration or Hard Drive Configuration.
5. Change SATA #1 to RAID.
6. Return to the previous screen by pressing the Escape key.
7. Select the Boot Menu by pressing the right arrow key.
8. Select Hard Disk Drives.
9. To assign the HP Smart Array B110i SATA RAID Controller as the boot controller, set Ctrl 1 to HP
Smart Array B110i SATA RAID Controller.
10. Press the F10 key to save the setting and to exit RBSU.
HP ProLiant 300 Series servers
To enable the controller and set boot order:
1. Power up the server.
2. When prompted during the start-up sequence, access RBSU by pressing the F9 key.
3. Select Advanced Settings.
4. Select Embedded SATA RAID.
5. Select Enabled.
6. Return to the previous screen by pressing the Escape key.
7. Select Boot Controller Order.
8. To assign the HP Smart Array B110i SATA RAID Controller as the boot controller, set Ctrl 1 to HP
Smart Array B110i SATA RAID Controller.
9. Press the F10 key to save the settings and to exit RBSU
포스팅 후 ORCA(Option ROM Configuration for Arrays)들어가셔서 Logical Drive를 잡으시면 됩니다.
다음은 동일 메뉴얼 6페이지 내용입니다.
To create a logical drive using ORCA:
1. Power up the server.
2. When prompted during the start-up sequence, access ORCA by pressing the F8 key.
3. Select Create Logical Drive.
The screen displays a list of all unconfigured physical drives and the valid RAID options for the
system.
4. Use the Arrow keys, Spacebar, and Tab key to navigate around the screen and set up the logical
drive, including an online spare drive, if one is required.
NOTE: You cannot use ORCA to configure one spare drive to be shared among several
arrays. Only ACU enables you to configure shared spare drives.
5. Press the Enter key to accept the settings.
Enabling and configuring the controller 7
6. Press the F8 key to confirm the settings and save the new configuration.
After several seconds, the Configuration Saved screen appears.
7. Press the Enter key to continue.
Repeat this procedure to create additional logical drives.
만약 POST후 F8키를 통한 ORCA진입이 안된다면 다시 RBSU에 진입하셔서 레이드컨트롤러를 부팅컨트롤러로 제대로 잡아놓았는지 확인해보시기 바랍니다.
Smart Array B110i SATA RAID Controller.
여기서 부터 막혔어요..
Advanced
Harddisk Configuration
SATA Mode Selection [RAID]
하고 Boot 메뉴 쪽을 보면 B110i 라는 글자는 찾아볼 수가 없네요 ㅠㅠㅠㅠㅠㅠ
Ctrl 1이 뭘 의미하는지 도통 이해가..
어떻게 하면 되나요..
참조하시고요...
b100i라고 안나오고 RAID:Smart Array로 나올겁니다.
그걸 재일 첫번째에 두면 부팅을 레이드에서 합니다.
문제는 저런 글자 하나도 찾아 볼 수가 없습니다;;;;
자꾸 신세만 지게 되는 것 같습니다...
레이드컨트롤러가 아직 disable되어있는듯 합니다.
여기서 제 경우엔
메뉴명이
Harddisk Configuration
레이드 옵션으로 바꾸는 것이
SATA Mode Selection [RAID]
이렇게 뜹니다..
이렇게 하고 부트 부분에 가 봐도 휑 하네요
DL120 G6인데
바이오스나 펌웨어가 구버전이라 그런 것 같습니다
HP 홈페이지처럼 바이오스가 생겨먹지 않았구요..
Hard Drive 하면서 드롭다운 메뉴 방식입니다..
그냥 HP에 전화 한번 해 봐야겠습니다..
이전에 다른 일 떄문에 내장 레이드가 있다는거 확실히 들었거든요..
관련 내용 다시 듣고 덧글로 회신하겠습니다..
새벽에 신세를 너무 많이 진 것 같습니다
조언과 도움 감사합니다
관련 커뮤니티를 보니
http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/DL120-G6-gt-Setup-RAID/td-p/5219767
사용하기 위해서는 최신의 펌웨어와 드라이버가 필요로 하다고 하는군요.